精品人妻少妇一区偷拍视频-精品人妻伦九区久久AAA片麻豆-精品人妻伦九区久久AAA片69-精品人妻伦九区久久AAA片-xxxx国产-xxxx成人

洞察行業資訊 分享專業知識

洞察行業資訊 分享專業知識

洞察行業資訊 分享專業知識

洞察行業資訊 分享專業知識

聯系我們

  • 全國統一服務熱線：

    134 1039 1245
    400-996-0787
    0755-8399 9818

  • 聯系郵箱：

    sales@faxytech.com

  • 聯系地址：

    深圳市福田區華強北路華聯發大廈602室

4db原則（法則）-英文原文 -福祿克DSX2-8000/DTX-1800

A YouTube video explaining how this this works is also?available from here.


This is applicable to the following cabling standards only:


ISO/IEC 11801

EN 50173

Aus/NZ

JIS


When?the Insertion Loss is less than 4.0 dB at the frequency point where the measurement is made, then the measurement is ignored and not uated against the selected Test Limit/Cabling Standard in the DTX CableAnalyzer. This is often referred to as the 4 dB rule. It is not applied in the North American TIA Cabling Standards. Only certain test parameters and configurations will have the 4 dB rule. The tables below indicate which link? definitions and test parameters have the 4 dB rule applied to them. As an aid, the other rules are also listed.


1.png

2.png


On a?short link, the Insertion Loss may never reach 4.0 dB. If that were to happen, then the entire measurement would be?ignored, or as the cabling standards phrase it; “recorded for information only”. If this were to happen with your DTX CableAnalyzer, you would see an “i” appear next to the summary result for that test parameter. In LinkWare software, the result would be recorded with “N/A’. An example is shown below:


3.gif


Concern is normally caused when the result has a negative margin. In this example we see the NEXT margin was -9.7 dB. A?negative margin is normally associated with a FAIL, but because the entire link never exceeded 4.0 dB Insertion Loss, it’s not a FAIL. Further?confusion lies in that the North American ANSI/TIA/-568-C.0 cabling standard does not have this 4 dB rule. If you were to test the same link above?with the same DTX CableAnalyzer, but using the North American Standard TIA Cat 5e Perm. Link, your result would be a FAIL.


4.gif


Please make sure you?have agreed in a Test Limit, in writing, before the project starts.


Let’s review in detail how this works by looking at another example test result on the DTX CableAnalyzer.


An ISO11801 PL Max Class D AUTOTEST was run on a short 6.0 m installed link, giving the following result:


5.gif


Looks normal. Let’s take a look at the NEXT result in a little more detail:


6.gif


You will observe that?the limit line has two colors, black and red. The cabling standards do not require the cable tester manufacturer to display where the 4 dB rule is implemented to the user, only that it is implemented. However, the DTX CableAnalyzer will indicate where the 4 dB rule has been implemented by changing the color of the limit line. If the?limit line is black,?the Insertion Loss was less than 4.0 dB. If?the limit line is red,?the Insertion Loss was 4.0 dB or greater. So for this Pair 1,2-4,5 the NEXT is not uated below 84.8 MHz. Let’s take a quick look at the Insertion Loss for Pair 4,5:


7.gif


As you can see, the Insertion Loss reached 4.0 dB at 84.8 MHz, as previously indicated in the NEXT Pair 1,2-4,5 graph above. NEXT contains two pairs. So which Insertion Loss pair do we use to implement the 4 dB rule? The disturbed pair is used for uation purposes. So if the worst case NEXT Pair was 1,2-7,8 then the?DTX CableAnalyzer would use the Insertion Loss values from Pair 7,8 to determine where the 4 dB rule is implemented.


As previously mentioned, if the link is particularly short, then the Insertion Loss may never reach 4.0 dB and the entire NEXT result is “ignored”. Let’s take a closer look at the first example where the test result was:


8.gif


Looking at the worst case NEXT result, we see the entire limit line is black, suggesting that the Insertion Loss for Pair 4,5 never reached 4.0 dB:


9.gif


Looking at the Insertion Loss for Pair 4,5:


10.gif


We see that the Insertion did indeed never reach 4.0 dB, so the entire measurement is not uated against the limit line (ignored) and recorded as “i” Information Only. If this result was downloaded to LinkWare Software, the report would show N/A against this measurement:


11.gif


No further action is required by the installer. This is a valid standards compliant result.

相關配件（）
主站蜘蛛池模板： 松滋市| 常州市| 德江县| 抚宁县| 红原县| 焦作市| 安乡县| 定陶县| 玛纳斯县| 巴楚县| 鄂托克前旗| 大姚县| 聂荣县| 梅河口市| 五常市| 岗巴县| 崇信县| 内江市| 尼勒克县| 揭阳市| 彝良县| 慈溪市| 北安市| 绥江县| 蕉岭县| 克东县| 绩溪县| 博兴县| 安阳县| 偏关县| 兴仁县| 宁南县| 许昌市| 磐石市| 彭山县| 碌曲县| 勐海县| 巴林右旗| 老河口市| 厦门市| 秭归县|